AZ DIY SCREENS

Measure with Confidence

DIY Measuring Help

Measuring for custom screens and roller shades is easier than you may think. Follow the instructions below, record each opening separately, and always list the width first, followed by the height.

If you are unsure about an opening, send us your measurements and a few photos. We can review them before you order or arrange professional measuring and installation.

Important: Custom products are made to the measurements you provide and may not be returnable. Measure twice, check your numbers, and contact us before ordering if anything is unclear.
Before You Measure

You will need:

  • A steel tape measure
  • A pencil or pen
  • Our measuring worksheet
  • A step ladder, if necessary
  • A phone or camera for reference photos

Measuring Tips

  • Use a steel tape measure, not a flexible cloth tape.
  • Record width first, then height.
  • Measure every opening, even if the windows appear identical.
  • Label each opening by room and location.
  • Measure to the nearest increment shown on our order form.
  • Do not make your own clearance deductions unless our product instructions specifically tell you to.
  • Check for handles, locks, cranks, trim, security sensors, or other obstructions.
How to Measure an Existing Window Screen

This is the easiest and most reliable method when the existing screen fits correctly.

Step 1: Remove the Screen

Carefully remove the existing screen from the window. Wear gloves and eye protection, and do not lean outside an elevated window.

Step 2: Measure the Width

Measure from the outside edge of the screen frame to the opposite outside edge. Measure near the corners rather than across a bowed section in the middle.

Step 3: Measure the Height

Measure from the outside edge at the top of the frame to the outside edge at the bottom. Record your measurement as: Width × Height.

Step 4: Measure the Frame Thickness

Measure the thickness or depth of the aluminum screen frame. This helps us match the new screen to the existing window channel.

Step 5: Identify the Hardware

Note the type and location of springs, pull tabs, clips, plungers or pins, crossbars, and other fasteners. If the screen has a crossbar, measure from the bottom of the screen frame to the center of the crossbar.

Helpful Photo

Place the removed screen on a flat surface and send us one photo of the entire screen, one close-up of the frame profile, and one photo of each type of spring, clip, or pull tab.

How to Measure for a New Bug Screen

If you do not have an existing screen to copy, we will need measurements of the screen channel or mounting area.

Step 1: Find the Screen Channel

Look for the tracks, channels, clips, or stops that will hold the screen in place.

Step 2: Measure the Opening

Measure the available width at the top, middle, and bottom. Then measure the available height at the left, center, and right. Record all six measurements. Do not automatically subtract from the opening size because the required allowance depends on the window and mounting system.

Step 3: Check the Mounting Method

Look for a recessed channel, spring pockets, exterior clips, plunger-pin holes, turn buttons, or a lip or stop that holds the frame.

Step 4: Send Us Photos

When no existing screen is available, photos are especially important. Include the entire window plus close-ups of the top, bottom, and side channels. Not sure what you’re looking at? Send us the measurements and photos before ordering.

How to Measure for Solar Screens

Solar screens can be mounted within an opening or over the exterior window frame.

Option 1: Replace an Existing Solar Screen

If your current solar screen fits properly: remove the screen, measure the outside frame width, measure the outside frame height, measure the frame thickness, and note the location of all clips, plungers, or mounting hardware. Record the width first and height second.

Option 2: Measure for a New Solar Screen

When adding a solar screen to a window that does not currently have one: decide where the finished screen will sit, measure the intended mounting area in three places across the width, measure in three places down the height, identify how the screen will attach, check for trim, handles, security sensors, stucco, or other obstructions, and take photos showing the full window and mounting surface.

The correct finished size can depend on the window frame and mounting hardware. Do not make a deduction unless directed by our ordering instructions.

How to Measure a Sliding Patio Screen Door

The Best Method: Measure the Existing Door

If the current screen door fits and operates correctly: remove the door and place it on a flat surface, measure the frame from outside edge to outside edge, record the width first and then the height, measure near the corners because the center of the frame may be bowed, do not include adjustable rollers in the frame measurement, measure the frame thickness, note the handle location and latch style, and tell us whether the handle is on the left or right when viewed from outside.

If You Do Not Have an Existing Door

Measure the patio-door screen tracks rather than the glass door itself. Identify the upper screen channel and lower screen track, measure the track-to-track height at the left, center, and right, measure the available door width, measure the depth of the track and available frame thickness, check that the track is straight and undamaged, take close-up photos of the upper channel and lower track, and send us the measurements and photos for review.

Sliding-door measurement methods vary by track and roller system. We recommend having us verify a patio-door order when there is no properly fitting door to copy.

Inside Mount vs. Outside Mount Roller Shades

Before measuring an interior or exterior roller shade, decide how it will be mounted.

Inside Mount

An inside-mount shade is installed inside the window or opening.

Advantages: Clean, built-in appearance. Window trim remains visible. Shade stays within the opening.

Check before choosing: Is the opening deep enough for the brackets and roller? Is the opening reasonably square? Are there handles, locks, cranks, or trim in the way? Are you comfortable with small light gaps along the sides?

Outside Mount

An outside-mount shade is installed on the wall, trim, or surface surrounding the opening.

Advantages: Provides greater coverage. Helps reduce light gaps. Can cover an opening that is shallow or out of square. Can make a window appear larger. May clear handles or other obstructions.

Outside mounts cover beyond the opening, so you must specify the complete area you want the finished shade to cover.

How to Measure Interior Roller Shades

Inside Mount

  1. Measure the Mounting Depth. Measure from the front of the opening toward the glass at the location where the brackets will be installed. Compare this measurement with the minimum depth required for your selected shade.
  2. Measure the Width. Measure the inside width at the top, middle, and bottom. Record all three measurements.
  3. Measure the Height. Measure the inside height at the left, center, and right. Record all three measurements.
  4. Check for Obstructions. Look for window cranks, handles, locks, sensors, trim, or anything else that could interfere with the shade.
  5. Do Not Make an Unlisted Deduction. Submit the opening measurements as directed on the order form. If our manufacturing specifications include an inside-mount allowance, we will apply it.

Outside Mount

  1. Decide Where the Shade Will Be Installed. Mark the intended top of the roller or headbox.
  2. Measure the Coverage Width. Measure the complete area you want the shade and fabric to cover. Include the desired overlap beyond each side of the window.
  3. Measure the Coverage Height. Measure from the planned top of the shade to the lowest point you want it to reach.
  4. Check the Mounting Surface. Make sure there is sufficient flat space for the brackets and that the shade will clear trim, handles, and other obstructions.
  5. Order the Complete Finished Size. Outside-mount shades are generally produced to the ordered dimensions rather than receiving the clearance deduction used for an inside mount.
How to Measure Exterior Roller Shades

Exterior roller shades may be mounted inside an exterior opening or on the face of the wall, columns, beams, or patio structure.

Inside-Mount Exterior Shade

  • Confirm that the opening has enough depth for the roller, brackets, and any side-retention system.
  • Measure the width at the top, middle, and bottom.
  • Measure the height at the left, center, and right.
  • Note the narrowest and widest measurements.
  • Check whether the walls or columns are square and parallel.
  • Identify any lights, outlets, handles, trim, or other obstructions.
  • Photograph the full opening and both mounting surfaces.

Outside-Mount Exterior Shade

  • Decide whether the brackets will attach to the wall, trim, beam, or columns.
  • Measure the total width you want covered.
  • Measure from the intended top of the roller to the desired stopping point.
  • Include the desired overlap beyond the opening.
  • Confirm that the mounting surface is solid, flat, and wide enough for the brackets.
  • Check for doors, handles, furniture, railings, and other obstacles.
  • Take photos of the complete installation area.

Motorized Exterior Shades

For a motorized shade, also tell us where electrical power is available, which side you prefer for the motor, whether an outlet is nearby, whether wiring will be concealed or surface mounted, and if the shade will connect to a remote, wall control, or home-automation system. Motor and power requirements vary by product, so we will confirm these details before your order is finalized.

What Photos Should I Send?

When asking for help, send:

  • One full photo of the opening
  • One photo of the top
  • One photo of the bottom or sill
  • Close-ups of both side channels or mounting surfaces
  • Photos of clips, springs, tracks, handles, or obstructions
  • A photo showing the tape measure in place, if possible

Label your photos to match your worksheet, such as Kitchen Window 1, Primary Bedroom West Window, Patio Door, or Covered Patio South Opening.

Screen Installation Hardware Guide

Screen hardware holds the screen securely in the window, creates the proper tension, and makes the screen easier to install and remove. The right hardware depends on your window, screen location, frame style, and existing mounting system. If you are replacing a screen that fits correctly, matching its current hardware and placement is usually the best starting point.

When ordering, tell us which hardware you need and where it is located on the screen. If you are unsure, send us photos of the existing screen and window opening.

Pull Tabs

Pull tabs give you a safe place to grip the screen during installation and removal. They generally do not secure the screen. Springs, clips, plungers, or other hardware hold it in place.

Tension Springs

Tension springs compress as the screen is inserted, then push outward to hold the screen snugly in its channel. They are commonly paired with pull tabs. Springs must be placed on the correct side of the screen. Match the location on your existing screen whenever possible.

Leaf Springs

Leaf springs are flat, heavier-duty springs that create pressure between the screen and window channel. They may require additional space because part of the spring can extend beyond the screen frame even when compressed.

Wire Springs

Wire springs are shaped pieces of spring wire that compress against the window channel to create holding pressure. They are often placed near the corners on one side or along the top of the screen.

Spring Plungers or Plunger Pins

Spring plungers are retractable metal pins installed in the screen frame. The pins extend into matching holes or grooves in the window frame to lock the screen in place. To remove the screen, pull the finger grips to retract the pins, then carefully lift the screen away.

Acorn Pointers

Acorn pointers are small projecting fasteners that fit into corresponding holes in the window frame. They help position and retain the screen and are normally used only when the window already has the correct receiving holes.

Casement Clips or Turn Clips

Casement clips rotate over the edge of the screen frame to hold the screen against the window. They are typically attached to the window frame with screws. Rotate the clips away from the screen for removal, then turn them back over the frame after installation.

Butterfly Latches or Knife Latches

Butterfly latches slide or rotate a small metal flange from the screen frame into a groove or notch in the window. Unlike spring plungers, butterfly latches are not spring-loaded. The small handle is moved manually to extend or retract the latch.

Slide Locks

Slide locks move a small pin or flange into the window frame to secure the screen. They provide a positive locking point rather than relying only on pressure.

Ram Horn Clips

Ram horn clips are curled metal clips that hook over a lip or edge in the window frame. They are commonly found on some older aluminum windows and may be installed along the top, bottom, or one side of the screen.

Friction Hangers and Wire Loops

Friction hangers hold one edge of the screen while wire loops secure the opposite edge over specially shaped fasteners. This type of hardware is most commonly associated with wood windows.

Exterior Solar-Screen Clips and Screws

Exterior clips hold a solar screen against the outside of the window frame. Screws attach the clips to the surrounding frame or mounting surface. Rotating clips make the solar screen removable for cleaning or maintenance.

Patio Screen Door Hardware

Sliding patio screen doors may require rollers, a handle and latch, a bug sweep, and track components. When ordering a patio screen door, provide photos of the upper track, lower track, rollers, handle, latch, and closing side.

How to Identify Your Hardware

  • Does the screen compress to one side during removal? It may use tension springs, leaf springs, or wire springs.
  • Do you pull small pins to release it? It probably uses spring plungers.
  • Do small clips rotate over the frame? It likely uses casement or turn clips.
  • Does the hardware hook over a window-frame lip? It may use ram horn clips.
  • Are there small holes in the window channel? The screen may use plungers or acorn pointers.
  • Are the visible pieces only used as handles? They are likely pull tabs and are not the parts securing the screen.

What to Include With Your Order

For the best match, provide the hardware type, number of pieces, location of each piece, distance from the nearest corner, screen frame thickness, photos of the existing hardware, photos of the matching window channel, holes, or clips, and which side of the screen faces indoors.

Not Sure? Let Us Check It.

DIY does not mean doing it alone. Send us your measurements, photos, and questions before placing your order. We can help confirm the product, mounting style, and information we need.

If you would rather not measure or install it yourself, ask about our complete measuring and installation service. Measure it yourself, ask for a little help, or let us handle everything. The choice is yours.